美国阿夸莎娜Aquasana EQ-400 除氯离子全屋中央净水机 国内现货

主滤芯带除氯离子功能，整体净水量为40万加仑左右。全屋净水系统 (带安装套件和前置滤芯，后置滤芯)

买家支付运费。

EQ-400R设计过滤流量：400000加仑 （美制1加仑=3.785升，40万加仑=1514立方米）

全新，国内现货。买家支付运费。

EQ-300 全屋净水系统 (带安装套件和前置滤芯，后置滤芯)

长使用寿命，高质量的净水系统，是您家庭全屋净水优选产品。

接口尺寸：3/4英寸 需要使用转换接头接入国内标准水管系统。

中间主滤芯EQ-400R的尺寸是 高度：145厘米，直径：32厘米。

品牌简介：Aquasana是美国著名的家庭净水器品牌，其采用Aquasana Claryum专利滤芯的净水器具有三重过滤技术：高等级活性碳、ATS离子交换树脂及超滤，通过了UL（美国保险商实验室）依据ANSI/NSF标准42&53的测试。

EQ-400R设计过滤流量：400000加仑 （美制1加仑=3.785升，40万加仑=151.4万升=1514立方米） 过滤量达到40万加仑后，建议更换。（使用小技巧，水质好的地方可以延长使用年限，每3-6个月更换前置滤芯可以延长主滤芯使用寿命）

关注整体健康

HT161226LX-001 + HT161226LX-006 + HT161226LX-019

安装注意事项Installation instruction:

1.始终保持单位处于正确的位置。

2.从主机壳上的入口和出口卸下红色装运盖。

3.通过“浪涌冲洗”对设备进行预冲洗：在最终安装之前正确冲洗该系统非常重要。底部罐中使用的颗粒状碳介质含有1-2％体积的碳细粉，应在使用前冲洗掉。从介质床中清除这些碳细粉的最佳方法是“浪涌冲洗”：使用提供的适配器，将花园软管连接到入口端口，以便水流入系统并流出出口。慢慢打开水，让变色的水从出水口流入水桶或排水管。由于碳细粉，前几加仑会出现黑色和混浊。在最初的15分钟冲洗后，开始一段“喘振潮”。打开水源30秒，然后反复关闭30秒，持续15分钟或直到水的初始冲洗完全清除，没有变色和浑浊。正确冲洗设备后，确保在进口和出口端口内正确设置了白色垫圈。将其与花园软管断开，并将其放置在最终安装位置。

4.安装前关闭主水源。

5.使用随附的组件将设备安装到主要供水系统上。不要过度拧紧配件，因为这可能会导致泄漏和配件损坏。不要使用管道涂料。管道涂料的使用会使保修失效。您可以使用NSF认证的管道底漆，胶水和水管工的胶带。留下两到三个线程暴露，不要超过七层管道工的磁带。超过七层将导致接头破裂和泄漏。

6.重要提示：必须牢固地支撑入口管道组件（阀门，预过滤器，主过滤器单元，接头和接头）。

7.安装完成后，慢慢打开水并检查是否有泄漏。

8.安装设备并检查是否有泄漏后，打开最靠近已安装设备的水龙头，让水在最后冲洗期间运行5-10分钟。

1. KEEP THE UNIT IN AN UPRIGHT POSITION AT ALL TIMES.

2. Remove the red shipping caps from the inlet & outlet ports on the main housing.

3. Precondition the unit by "surge flushing": It is very important that this system is flushed properly prior to final installation. The granular carbon medium used in the bottom tank contains 1-2% by volume of carbon fines that should be flushed out prior to use. The best method for purging these carbon fines from the media bed is "surge flushing": Using the supplied adapter, connect a garden hose to the inlet port so that the water will flow into the system and out of the outlet port. Slowly turn on the water and allow the discolored water to flow from the outlet into a bucket or drain. The first few gallons will appear black and cloudy due to carbon fines. After an initial 15 minute flushing, begin a period of "surge flushing." Turn the water supply on for 30 seconds and then off for 30 seconds repeatedly for 15 minutes or until initial surge of water is completely clear and free from discoloration and cloudiness. Once the unit has been properly flushed, be sure the white washers are properly set inside the inlet and outlet ports. Disconnect it from the garden hose and position it for final installation.

4. Turn off main source water supply prior to installation.

5. Install the unit to the main water supply using the supplied components. Do not over tighten fittings, as this may cause leakage and broken fittings. Do NOT use pipe dope. The use of pipe dope voids the warranty. You may use NSF Certified pipe primer, glue and plumber's tape. Leave two-three threads exposed and do not exceed seven layers of plumber's tape. More than seven layers will cause the nipple to crack and leak.

6. IMPORTANT: The inlet piping assembly (valve, pre-filter, main filter unit, union and nipples) must be firmly braced and supported.

7. Once installation is complete, slowly turn the water on and inspect for leaks.

8. Once the unit is installed and checked for leaks, open the water faucet closest to the installed unit and allow water to run for 5-10 minutes for the final flushing period.